Uncategorized

Range hood hook up

Toolbox Calculators Budget Green Living. Today's Homeowner Full Episodes. May 26th, at 8: Tips for Today's Homeowner Sign up for our Tips for Today's Homeowner newsletter and stay updated on how to improve your home! Creating a Multipurpose Room Nov 13, Reproduction in whole or in part without permission is prohibited.

DIY How to Replace a Kitchen Hood Fan

Sizing Kitchen Range Hoods. Over the Range Venting.


  1. still dating my wife!
  2. Installing the Range Hood (NK30K7000 & NK36K7000);
  3. dating free.com!
  4. !

Importance of a Vented Range Hood. Lift the hood slowly off the screws, put the hood down, and remove the loosened screws. Purchase your new range hood. Make sure the range hood is large enough to cover your stovetop and that your space above the stovetop leaves at least 24 inches If you can, purchase a range hood that extends at least one inch 2.

Buy a hood with the correct CFM rating. The cfm rating represents how much air the vent can pull each minute, or c ubic f eet per m inute.

Included Parts

To find the right cfm rating for your kitchen, multiply the square footage of your kitchen by 2. Make sure the range hood you are buying is the correct size that will fit. The most common sizes are 36in, 48in, and 60in. Range hoods will vent either through the cabinets above or through the wall. If you're buying a new range hood and dealing with a pre-existing vent pipe, make sure that both connect easily. If, for example, the range supports cabinet upper venting but your existing vent pipe goes through the wall directly behind the vent, you're going to have trouble connecting the two.

Disassemble the cover of the range hood as well as the fan and filter underneath. Remove the filters first, then use a screwdriver to remove the bottom panels.

How to Replace a Range Hood in Your Kitchen | Today's Homeowner

Next, unscrew the duct connector, which is usually attached to the underside of the bottom panels in order to prevent damage during shipping. Finally, remove the perforated duct knockout from the back of the hood. Use a slotted screwdriver and a hammer for this, but be sure to work gently so that you don't damage any metal around the knockout.

For safety, shut off the electricity to circuit supporting the range at the main electrical panel. Next, make sure light and power switches on the old hood are off. If your range hood is a plug in, just unplug it and skip this step. Use the template or instructions that came with your hood to mark the spot in your wall or cabinet for the vent cutout. Most range hoods will come with a manufacturer's template. Use a laser level or water level to help you mark the exact middle of the wall. Then line your template up with the middle of the wall and tape it off. You're ready to start drilling for your cutout.

Of course, the cutout in the wall needs to match the knockout in the range hood perfectly. If you need to, drill for the electrical wiring as well. If you're not familiar with electrical work, call an electrician to spec the job for you. Drill or cut for the vent. Use a drill or wallboard saw to cut through the drywall to get the templated shape of your cutout. If the space behind the wall is not occupied by any studs or piping, consider yourself lucky!

If it is, there are several workarounds you can use. Work around any obstacles you find in your cutout. If, while cutting out the opening for the exhaust vent, you come across piping, you'll have to call an audible. Open up a larger rectangle of the wall so you can work freely. Then, you'll have to do three main things: Reroute and re- solder the pipe so that it leaves your opening entirely free. If you are not familiar with this type of job, it's best to call a professional plumber or general contractor to help you. Drill 1 x 3 cleats to the top and bottom of the wall to support the new wall patch.

This will give the new wallboard that covers up the opening structural support. Drill, tape, and mud the new wall patch to cover up the hole entirely. Then, when it's dry, remove the original cutout for the exhaust again with your template.

How to Replace a Range Hood in Your Kitchen

Follow the same procedure as before. Install any necessary ductwork so that it leads safely outside of your home. Remember that the venting cannot terminate inside the wall or attic — the exhaust must travel through duct outside of the home. Mark the holes for the screws and cable. If you have a template, now is the time to use it.

Otherwise, hold the hood into place and have a partner mark inside the holes for the screws. Drill the mounting brackets or screws into the wall or cabinet above. Where you drill the screws depends largely on whether you're mounting your hood directly into the wall or into existing cabinetry. If you are mounting directly into a wall using brackets, drill the screws fully into the wall; if you are mounting into existing cabinetry, drill the screws only halfway into the cabinetry — you want the range hood to be able to slip over these screws and rest on top of them.

grupoavigase.com/includes/248/6827-busco-chica-para.php If you're mounting into the wall, for example, and the wall is tiled, use a nail set and hammer to tack small holes into the tile. This way, you're less likely to damage the tile when you drill your mounting brackets directly into the wall. If the cabinet is thin, you might need to install wooden blocks to accommodate and strengthen the mounting screws.

The vent should match the hole for the ductwork for vented range hoods. Realign the hood as needed before tightening the screws. Run the cable from inside the wall through the cable hold in the hood. The fan and light both have black and white wires that must be attached. If you have never done an electrical project before or don't fully understand the manufacturer's electrical instructions, call an electrician to help you out.

Connect the two black wires from inside the hood to the one black wire from inside the wall. Repeat this process with the white wires. Fasten the green grounding wire coming from the wall to a grounding screw on the range hood. If you are using a plug in hood, install an electric plug if you don't have an existing plug. Then plug in your hood. Reattach the filters to the hood and fasten any grease guards back onto the hood. Then, replace the hood cover by tightening the screws. Reset the power and test the workability of the fan and light.

No, it's not fire containing and will melt readily so it is not recommended to use for this. Not Helpful 0 Helpful 3. My vent hood said it could be vented or ventless. It was installed vented, but I feel air being discharged from the grill on the hood.